Electrical switchgear equipment

NEW SWITCHGEAR MANUFACTURING / RESOURCES

What Size Switchgear Do I Need?

The right switchgear size begins with a calculated electrical load, not a cabinet dimension or a simple comparison with an existing lineup. An engineer should identify connected loads, demand factors, motor…

U.S.Manufacturing focus
NewCustom project-led builds
NationwideProject support
Made in the USA
Short lead times, confirmed per project
UL 891 subject to project scope
Nationwide delivery planning

Start With the Electrical Load

The right switchgear size begins with a calculated electrical load, not a cabinet dimension or a simple comparison with an existing lineup. An engineer should identify connected loads, demand factors, motor starting behavior, continuous loads, nonlinear loads, and the operating schedule that applies to the facility. The result helps establish continuous current for mains, bus, and feeders while also revealing whether separate source sections or a different distribution arrangement may be appropriate. A manufacturer can build new custom switchgear to the resulting requirements, but the load study remains a project responsibility that must be reviewed by a qualified professional.

Match Voltage, Phase, and Frequency

Current alone does not determine equipment size. The specification should identify nominal system voltage, equipment voltage class, phase, wire configuration, frequency, grounding method, and the service or feeder role. A 480-volt three-phase lineup, for example, presents different device, insulation, clearances, and connection questions than a lower-voltage arrangement, even when the calculated amperage appears similar. Confirm the utility or upstream source information, transformer data, and downstream distribution interfaces before requesting a quote. American-made switchgear with American components can be configured around documented project inputs, while the final design must follow engineering review.

Account for Fault Duty and Protection

A properly sized lineup must withstand and interrupt the electrical duty identified for its location. Available fault current, short-circuit current rating or withstand requirements as applicable, breaker interrupting ratings, bus bracing, protective-device coordination, and grounding details all affect the specification. These values cannot be inferred safely from the main ampere rating. Request the available-fault-current study or the engineer’s design basis, then coordinate breaker settings and time-current characteristics across the distribution system. If UL 891 is relevant to a switchboard project, its applicability, construction requirements, and any project-specific listing or capability must be confirmed rather than assumed.

Plan for Environment and Physical Fit

Physical and environmental conditions can change the appropriate enclosure, layout, and usable capacity. Identify whether the equipment is indoors or outdoors, the surrounding temperature, moisture, dust, corrosive exposure, altitude considerations, access restrictions, cable-entry direction, working clearances, and the route from receiving to the installation point. Room dimensions and maintenance access may determine whether the lineup needs shipping sections or a revised arrangement. Include elevations, conduit locations, lifting information, and anchorage interfaces in the design package so a custom builder can coordinate the equipment with the site instead of sizing only by electrical current.

Allow for Useful Future Capacity

Future capacity should be defined deliberately rather than added as an arbitrary percentage. Discuss planned feeders, known expansion phases, spare circuit spaces, bus capacity, transformer growth, generator or renewable-energy interfaces, and the physical room available for later work. Extra space does not automatically mean extra ampacity, fault capability, or compatible protection, so each allowance should be described in the one-line diagram and equipment schedule. The manufacturer can evaluate a custom new lineup against those stated provisions, while the engineer should confirm that future assumptions do not distort present coordination, clearances, heat considerations, or operating sequences.

Prepare a Complete Quote Package

For a useful manufacturer quote, provide the one-line diagram, load summary, voltage and grounding data, available fault current, protection and coordination requirements, enclosure location, dimensions, cable details, control schemes, metering needs, documentation expectations, destination, and any installation constraints. State which components are required and identify interfaces with transformers, generators, transfer equipment, busway, or downstream panels. Switchgear Builders manufactures and supplies new electrical switchgear in the United States, custom to specification, using American components and nationwide shipping. Project-specific review will determine the final configuration, applicable requirements, shipping plan, and commercial scope.

GOOD TO KNOW

Questions & answers.

Practical answers to help you plan the next step.

Does a higher ampere rating automatically mean the switchgear is correctly sized?

No. Ampere rating must be evaluated with voltage, fault duty, protection, enclosure conditions, physical fit, and the calculated load.

What information should I send when asking for new switchgear?

Send the one-line diagram, load calculations, system voltage, grounding, fault current, dimensions, controls, destination, and documentation requirements.

How much future capacity should a project include?

Future capacity should reflect documented expansion plans, spare feeders, bus capability, room constraints, and engineering coordination rather than an automatic percentage.

Can Switchgear Builders determine the required size without an engineering review?

The manufacturer can coordinate a custom quote from supplied project data, but a qualified engineer should establish and approve the electrical design basis.

LET’S BUILD SOMETHING THAT WORKS

Tell us about your project.

Share the essentials and start a conversation about new switchgear requirements, specifications and schedule.

Call (951) 403-5738

This form opens your configured email app to prepare a message. Send it from your email app, or contact saleselectricalbuyers@gmail.com directly.

All fields are required. Your email app is needed to send this request.

Request a quote