Electrical switchgear equipment

NEW SWITCHGEAR MANUFACTURING / RESOURCES

Interrupting Rating Definition

Interrupting rating is the fault current that a protective device is rated to interrupt under specified conditions. It is commonly expressed in amperes and is associated with a particular voltage, frequency…

U.S.Manufacturing focus
NewCustom project-led builds
NationwideProject support
Made in the USA
Short lead times, confirmed per project
UL 891 subject to project scope
Nationwide delivery planning

Interrupting Rating: The Core Definition

Interrupting rating is the fault current that a protective device is rated to interrupt under specified conditions. It is commonly expressed in amperes and is associated with a particular voltage, frequency, device type, and application. When a fault occurs, a circuit breaker or fuse must open the circuit and stop current flow without exceeding its tested interrupting capability. The rating is therefore not a prediction of normal load current; it addresses the much larger current that can be available during a short circuit. A useful interrupting rating definition always identifies the device and the conditions attached to its rating, rather than treating the number as a universal property of an entire lineup.

Why Available Fault Current Matters

The device interrupting rating must be evaluated against the available fault current at its installation point. That available current depends on the utility or generator source, transformer impedance, conductor arrangement, motor contribution, system voltage, and other network characteristics. An engineer typically obtains a short-circuit study or equivalent calculation before finalizing protective devices. If calculated fault current is greater than the device rating, the selection is not suitable for that application. A higher ampere frame or continuous-current rating does not automatically solve an interrupting-duty issue, so these values should be reviewed separately on drawings, schedules, and equipment submittals.

Interrupting Rating Versus Related Ratings

Interrupting rating is often confused with withstand ratings, short-circuit current rating, or continuous current rating. Continuous current describes the load a device or bus can carry during specified operating conditions. Withstand concerns the ability of an assembly or component to endure fault forces and thermal stress for a defined duration, while interrupting rating concerns a device opening the fault current. An assembly-level short-circuit current rating may depend on the combination of components and their permitted installation arrangement. Those terms can interact, but they are not interchangeable; the project specification should state which rating applies to each device and assembly.

Inputs for a New Switchgear Specification

For a manufacturer to prepare new custom switchgear, the technical package should identify nominal system voltage, frequency, phase and grounding arrangement, source information, calculated available fault current, main and feeder devices, protection requirements, enclosure conditions, and the one-line diagram. Include whether the equipment is indoors or outdoors, the physical lineup constraints, cable entry preferences, metering, control wiring, and documentation expectations. American components can be incorporated according to the defined project scope, and Switchgear Builders supplies new equipment with nationwide shipping from the United States. The final interrupting-duty selection remains subject to engineering review and the specified project conditions.

Reviewing Devices and Coordination

A practical review compares the calculated fault current with each main and feeder protective device at the voltage where it will be installed. The review should also consider selective coordination, instantaneous settings, time-current curves, series combinations where specifically permitted, and the effect of alternate sources such as generators or tie breakers. Changes to transformer size, feeder routing, source configuration, or protective settings can change the study inputs. Ask the design engineer and manufacturer to reconcile the one-line diagram, device schedule, calculations, and control sequence before fabrication, rather than relying on a single rating printed in isolation.

How to Address Interrupting Rating in a Quote

A quote request should state the required interrupting rating or provide the available fault-current study and the assumptions behind it. Request a clear device schedule showing voltage, continuous-current rating, interrupting rating, trip or fuse information where applicable, and the location of each protective device. Also identify any required test plan, drawings, data sheets, and review milestones without assuming that a particular certification applies. Switchgear Builders can use these inputs to develop a manufacturer quote for new electrical switchgear built to specification; the customer, engineer, and installing contractor should confirm final design responsibility and field requirements.

GOOD TO KNOW

Questions & answers.

Practical answers to help you plan the next step.

Is interrupting rating the same as available fault current?

No. Available fault current is a system calculation, while interrupting rating is the protective device capability to interrupt fault current under specified conditions.

Does a larger continuous-current rating guarantee adequate interrupting duty?

No. Continuous-current capacity and interrupting capability address different stresses, so both values must be checked against project calculations and device data.

What information should accompany an interrupting rating request?

Provide voltage, source details, fault-current calculations, one-line diagrams, device locations, system configuration, and any required coordination or documentation criteria.

Can interrupting rating change during a switchgear project?

Yes. Source changes, transformer revisions, feeder modifications, or alternate operating modes can change available fault current and require a renewed engineering review.

LET’S BUILD SOMETHING THAT WORKS

Tell us about your project.

Share the essentials and start a conversation about new switchgear requirements, specifications and schedule.

Call (951) 403-5738

This form opens your configured email app to prepare a message. Send it from your email app, or contact saleselectricalbuyers@gmail.com directly.

All fields are required. Your email app is needed to send this request.

Request a quote